100 Victoria Street

A grand entrance to one of the three buildings making up Cardinal Place

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Nunc porta ornare scelerisque. Cras ut tincidunt leo. Nunc vulputate leo vel consequat dapibus. Phasellus in maximus augue, eget mattis mi. Maecenas nisl elit, egestas et libero at, sodales accumsan nibh.

1 of 4
The Basalt Range
The Basalt Range

Large format porcelain tiles

Inspired by basalt rock, this sophisticated and versatile range is available in 3 neutral tones, 3 finishes and 7 formats.

About the Basalt range
  • 250 x 100
  • 100 x 100
  • 100 x 50
  • 60 x 60
  • 60 x 30
  • Matt
  • Bush hammered
  • Polished
Ardex P4 Primer
Ardex P4 Primer

Ready Mixed Rapid Drying Multi-Purpose Primer

ARDEX P 4 Primer can be used on internal and external walls, ceilings and floors. The consistency of ARDEX P 4 Primer has been optimised so that dripping and splashes are virtually eliminated. For use prior to the installation of ARDEX tile adhesives and floor-levelling compounds. ARDEX P 4 Primer produces a textured grip which facilitates tile on tile application, eliminating the risk of adhesives slipping when being applied to smooth surfaces. 

  • Ready mixed re-sealable tub for convenience and ease of use
  • Rapid drying - dries in as little as 30 minutes

  • White colour allows clear identification of primed areas

  • Moisture resistant - for internal and external use

  • Produces a textured grip surface

  • For use with ARDEX tile adhesives and floor levelling compounds

  • Suitable for a wide range of absorbent and non-absorbent substrates

  • Consistency which virtually eliminate drips and splashes so ideal for use on walls, floors and ceilings

  • Revolutionary, white, single component, solvent free system

Ardex X7001 and X7001 W
Ardex X7001 and X7001 W

Rapid Drying Flexible Floor Tile Adhesive

ARDEX X 7001/ARDEX X 7001W is a grey or white MICROTEC fibre reinforced rapid hardening and drying, flexible cement-based floor tile adhesive. It is ideal for fixing floor tiles to wood-based sheets and boards and other surfaces. The inclusion of the fibres reduces the possibility of the floor tiles cracking over board joints if movement of the timber occurs. 

  • Ideal for wood-based sheets and boards - RAPIDRY FORMULA reduces the risk of mix water affecting wooden substrates
  • Rapid hardening and drying - can be trafficked and grouted 2 hours after fixing
  • ARDEX X7001W white is ideal for fixing light and translucent marble and limestone
  • Excellent adhesion and easy to work
  • Use with all tile types including fully vitrified, porcelain and agglomerate stone
  • Mix consistency facilitates solid bedding 
Schlüter®-DILEX-AKWS
Schlüter®-DILEX-AKWS

Movement joint profile for areas subjected to mechanical stresses

Schlüter®-DILEX-AKWS is a maintenance-free movement joint profile for tile and natural stone surfaces subject to moderate mechanical stresses. 

Schlüter®-DILEX-AKWS offers secure edge protection for surfaces exposed to foot traffic or light vehicular traffic. The lateral anchoring legs, which feature trapezoid- shaped perforations, are connected by a 6 mm wide, soft plastic movement zone. The side sections of the profile provide effective edge protection for the surface covering. 

The relatively small width of the movement zone only allows for absorbing minor movements. This must be taken into account depending on project requirements. 

Schlüter®-DILEX-AKWS profiles interrupt the transmission of sound within the surface covering and reduce the transmission of impact and airborne sound.

  • Maintenance-free movement joint profile
  • Secure edge protection against foot traffic or light vehicular traffic
  • Reduce the transmission of impact and airborne sound